GCL Cable Station Requirements: At least 17,000 square feet (~1900m2) of total area Raised floor, with minimum load tolerance of 500 kg/m2 Useable height of at least 2.5m Dual cable vaults DC -48v power, with battery backup for at least 1 hour. AUTOSAR_EXP_LayeredSoftwareArchitecture.pdf [2] General Requirements on Basic Software Modules AUTOSAR_SRS_BSWGeneral.pdf [3] Specification of RTE AUTOSAR_SWS_RTE.pdf [4] Requirements on I-PDU Multiplexer AUTOSAR_SRS_IPDUMultiplexer.pdf [5] Specification of Communication AUTOSAR_SWS_COM.pdf [6] General Specification of Basic Software Modules The hardware configuration of the MUX can be changed by using the small switches found at the bottom of the MUX. MUX16 functional diagram Apply potential on all channels simultaneously It is not possible to apply a potential simultaneously to more than one sensor or cell each with three electrodes unless a two electrode system is used. Tree Decoder Mux qColumn mux can use pass transistors - Use nMOS only, precharge outputs qOne design is to use k series transistors for 2k:1 mux - No external decoder logic needed B0 B1 B2 B3 B4 B5 B6 B7 B0 B1 B2 B3 B4 B5 B6 B7 A0 A0 A1 A1 A2 A2 Y Y to sense amps and write circuits. 12Gbps HDMI 2-to-1 Active Mux Switch with Linear ReDriver The PI3HDX12221 is the latest HDMITM active switch with a Linear ReDriver™ and a signal mux from Diodes Incorporated supporting the HDMI 2.1 standard for data rates up to 12Gbps per channel. PI3HDX12221 has a 2-to-1 configuration with 4 differential channels. It provides programmable Four configurations are available: •Idle mode (default setting). ADC is not doing conversion in this mode. •Single sweep mode. The ADC sweeps sequentially the ADC-configured ports, from the lowest index port to the highest index port, once CNVT is asserted. •Single conversion mode. The complete working of a 4:1 MUX using the CD4052 simulation is shown in the video below, the image here shows a snapshot of it. As you can see in the above image, the channel select pins are 1 and 0 for A and B respectively. Meaning the Channel 1 that is X1 and Y1 is selected. So the input given to X1 and Y1 is reflected on the pins X and Y. The configuration software and all integration equipment must be connected to the same network as the processors. a. 1 To use standard networking, run a single Ethernet cable (CAT5 or better) from an existing The CFM-M4P-MUX Indoor Unit is intended for use with the CFM-L4 radios. The modularity of the CFM-MP-MUX IDU allows installing various CFM series traffic interface modules (for more information please refer to chapter 2.1). Local and remote management functionality (incl. Web, Telnet, SNMP, ASCII) Alarm interface (optional). Key programming and configuration features of MachXO3L devices are: † Instant-on configuration from internal NVCM (MachXO3L) or Flash (MachXO3LF) - powers up in milliseconds † Infinite number of configuration cycle through volatile SRAM technology † MachXO3L multi-time (up to nine times) programmability through non-volatile technology (NVCM) • One design is to use k series transistors for 2k:1 mux - No external decoder logic needed B0 B1 B2 B3 B4 B5 B6 B7B0 A0 A0 A1 A1 A2 A2 YY to sense amps and write circuits. NCD - Master MIRI 30 Single Pass-Gate Mux • Or eliminate series transistors with separate decoder A1 A0 B0 B1 B2 B3 Y. NCD - Master MIRI 31 Ex: 2-way Muxed SRAM • One design is to use k series transistors for 2k:1 mux - No external decoder logic needed B0